Search Term Record
Metadata
Name |
Thomsen, Niels Christian |
Related Records
-
-
Band, Metal - Thomsen, Mary Lou
A steel ring, likely from the end of a band driver. The ring has a rounded rectangular shape and has a silver and rust color to it. The top, bottom and sides are flat metal. One outside corner has a jagged edge. (Identified as a "Drivringe" as found on page 8 of donor's gift of cooper tool book titled "L.V. Erichsen / Bødkerværktøj".)
Record Type: Object
-
Band, Metal - Thomsen, Mary Lou
This is a metal band, (identified as a "Drivringe" as found on page 8 of donor's gift of cooper tool book titled "L.V. Erichsen / Bødkerværktøj"). The band has an oblong oval shape, but is more narrow in the middle than a normal oval. It has a cut-out center that is the same shape as the band itself. The outside surface appears to have been painted black and varnished; but the inside surface of the ring has not.
Record Type: Object
-
Bar, Rivet - Thomsen, Mary Lou
Rivet bar (identified as a "Nitteplade" as seen on page 8 of donor's gift of cooper tool book titled "L.V. Erichsen / Bødkerværktøj"). Heavy metal bar, rectangular in shape, horizontal in orientation. All sides are flat, corners are sharp 90 degree turns. Dark silver in color. There are five holes drilled into the top and through the bottom. The sizes of those graduate--smallest to largest. The holes run the long-way of the bar. running thr...
Record Type: Object
-
Bit - Thomsen, Mary Lou
This is an auger bit. It is used for wood or earth drilling. At the base of the bit is a small screw like spiral. Further up the spiral gets bigger until it stops about halfway up. Above this the rod is plain except for a point on the curve of the rod that has an engraved arrow pointing towards the viewers left. The arrow goes through two words. The top word is illegible but the bottom word is "SWEDEN". A number "6" is engraved below the arrow a...
Record Type: Object
-
Bit - Thomsen, Mary Lou
This is an auger bit. It is used for wood or earth drilling. At the base of the bit is a small screw like spiral. Further up the spiral gets bigger until it stops about halfway up. Above this the rod is plain except for a point on the curve of the rod that has an engraved rectangle inside of a rectangle. Inside the smaller rectangle reads: "The IRWIN Bit / Reg. U.S. Pat. Off.". Below the rectangles "MAINBOR" is engraved. At the end of the rod is...
Record Type: Object
-
Bit - Thomsen, Mary Lou
Pole bit, silver colored steel with a screw point below the spiral boring section. The end that goes into the driver has four sides and is pyramid shaped. Around the head of the bit is engraved "C__FALL / SWEDEN" and a "9".
Record Type: Object
-
Bit - Thomsen, Mary Lou
Pole bit, silver colored with a screw point above the boring section. The end that goes into the driver has four sides and is triangle shaped. On the bit is engraved/stamped: "The IRWIN Bit / Reg. U.S. Pat. / MAINBOR" and "12".
Record Type: Object
-
Bit - Thomsen, Mary Lou
This is an auger bit. It is used for wood or earth drilling. At the base of the bit is a small screw like spiral. Further up the spiral gets bigger until it stops about halfway up. Above this the rod is plain except for a point on the curve of the rod that has an engraved rectangle inside of a rectangle. Inside the rectangle is a symbol similar to the red cross, but the four ends are flared out slightly. Next to the symbol reads: "ROBT SORBY / ...
Record Type: Object
-
Bit - Thomsen, Mary Lou
This is an auger bit. It is used for wood or earth drilling. At the base of the bit is a small screw like spiral. Further up the spiral gets bigger until it stops about halfway up. Above this the rod is plain. At the end of the rod is a four-cornered pyramid. The four sides are flat, but have a scalloped shape at the top. One of the sides has "16 / SH" engraved into it. The tip of the pyramid ends with a dull point.
Record Type: Object
-
Blade, Plane - Thomsen, Mary Lou
Plane blade with adjusting plate held in place below blade with a screw. The blade is a dark rust color with some silver coloring showing on the circular bolt. The blade has a cut-out in the middle of it in the shape of a long rectangle with a circlular bolt at the top (the bolt has a notch at the top for tightening or loosening). Bottom side of blade has an engraving which is not completely visible due to corrosion and rust; outline of a lion i...
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A small, metal tool blade. The blade is rectangular and thin and is generally a dark rust color with a rough surface. One end has rounded edges and the other end has 3 saw tooth blades.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A metal blade with a hook at one end. The blade is rectangular and flat. One end has squared edges and the other has the hook shape. It is unclear what the tool is used for.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A metal blade predominantly rust colored. It is unclear what the tool is used for. The tool is flat and rectangular with squared edges at one end and an angled blade edge on the other.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
This tool is one of three pieces tied with a brown paper tie. It is unknown what this tool is for. This blade is rusted and stuck to another blade (2002.70.95c) and they do not come apart. The tool is flat and rectangular with one end sharpened and the other end with squared edges.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A small, silver metal tool with a hook appendage. This tool is one of three pieces tied with a brown paper tie. It is unknown what this tool is for. The tool is flat and rectangular with squared edges at one end and an "L" shaped appendage at the other.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
This tool is one of three pieces tied with a brown paper tie. It is unknown what this tool is for. This blade is rusted and stuck to another blade (2002.70.95b) and they do not come apart. The tool is flat and rectangular with one end sharpened and the other end with squared edges.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A small, metal tool blade. The blade is rectangular with square corners at one end and 3 saw tooth blades on the other end. The top side of blade has engraved letters of "(SA)NDUSKY TOOL Co / (SA)NDUSKY OHIO". On the flat bottom side of the blade there are engraved letters that say "DOK(EEFFE)".
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A metal blade attachment that has an appearance of a flying flag. The tool is a dark rust color. The tool has a long, rectangular, flat stem with a wide blade at one end. The blade has a concave curve.
Record Type: Object
-
Blade, Tool - Thomsen, Mary Lou
A metal blade attachment. The tool is long and rectangular with a blade on the short end of narrowed stem. The opposite end is a wide and jagged and appears to have been broken. A groove is etched down the center of the top of narrow stem and extends 3/4" into the wide end.
Record Type: Object
